View NL204153BC21-02_2919227.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

document number: dod-pd-0092 (2nd edition) published date: july 2003 cp(n) nec lcd technologies, ltd. 2003 all rights reserved. 1 all information is subject to change without notice. please confirm the sales representative before starting to design your system. tft color lcd module NL204153BC21-02 54cm (21.3 type) qxga preliminary data sheet dod-pd-0092 (2nd edition) www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 2 introduction no part of this document shall be copied in any form or by any means without the prior written consent of nec lcd technologies, ltd. (hereinafter called "nec"). nec does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a product described herein or any other liability arising from use of such application. no license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of nec or of others. while nec has been making continuous effort to enhance the reliability of its products, the possibility of failures cannot be eliminated entirely. to minimize risks of damage to property or injury to person arising from a failure in an nec product, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. nec products are classified into the following three quality grades: "standard" , "special" , "specific" the "specific" quality grade applies only to applications developed based on a customer designated "quality assurance program" for a specific application. the recommended applications of a product depend on its quality grade, as indicated below. customers must check the quality grade of each application before using it in a particular application. standard: computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots special: transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) specific: military systems, aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems (medical equipment, etc.) and any other equipment the quality grade of this product is "standard" unless otherwise specified in this document. if customers intend to use this product for applications other than those specified for "standard" quality grade, they should contact nec sales representative in advance. www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 3 contents introduction................................................................................................................... ....................... 2 1. outline ..................................................................................................................... .............................. 4 1.1 structure and principle .................................................................................................... ...... 4 1.2 applications ............................................................................................................... ..................... 4 1.3 features ................................................................................................................... ......................... 4 2. general specifications...................................................................................................... .......... 5 3. block diagram ............................................................................................................... ................... 6 4. detailed specifications..................................................................................................... .......... 7 4.1 mechanical specifications .................................................................................................. ... 7 4.2 absolute maximum ratings................................................................................................... .7 4.3 electrical characteristics ................................................................................................. .8 4.3.1 driving for lcd panel signal processing board ........................................................................... 8 4.3.2 driving for backlight lamp ............................................................................................... ............. 9 4.3.3 power supply voltage ripple .............................................................................................. .......... 10 4.3.4 fuse ..................................................................................................................... ........................ 10 4.4 power supply voltage sequence.........................................................................................11 4.5 connections and functions for interface pins ........................................................ 12 4.5.1 lcd panel signal processing board ........................................................................................ .... 12 4.5.2 backlight inverter....................................................................................................... ................. 14 4.5.3 positions of plugs and sockets........................................................................................... .......... 14 4.6 method of connection for lvds transmitter ........................................................... 15 4.7 10-bit look up table for gamma adjustment................................................................. 17 4.8 display colors and input data signals.......................................................................... 17 4.9 display positions .......................................................................................................... .............. 18 4.10 pixel arrangnment......................................................................................................... ........ 18 4.11 lvds data taransmission method.................................................................................... 18 4.12 input signal timings for lcd panel signal processing board ........................ 19 4.12.1 input signal specifications............................................................................................. ............ 19 4.12.2 input signals timing chart.............................................................................................. ............ 20 4.13 optics .................................................................................................................... .......................... 21 4.13.1 optical characteristics ................................................................................................. .............. 21 4.13.2 definition of contrast ratio ............................................................................................ ............ 22 4.13.3 definition of luminance uniformity...................................................................................... ..... 22 4.13.4 definition of response times............................................................................................ .......... 22 4.13.5 definition of viewing angles ............................................................................................ ......... 22 5. reliability tests ........................................................................................................... ................. 23 6. precautions................................................................................................................. ...................... 24 6.1 meaning of caution signs ................................................................................................... .. 24 6.2 cautions ................................................................................................................... ...................... 24 6.3 attentions................................................................................................................. ..................... 24 6.3.1 handling of the product.................................................................................................. ............. 24 6.3.2 environment.............................................................................................................. .................. 25 6.3.3 characteristics .......................................................................................................... ................... 25 6.3.4 other.................................................................................................................... ........................ 25 7. outline drawings ............................................................................................................ .............. 26 7.1 front view ................................................................................................................. .................... 26 7.2 rear view.................................................................................................................. ...................... 27 revision history............................................................................................................... .................. 28 www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 4 1. outline 1.1 structure and principle NL204153BC21-02 module is composed of the amorphous silicon thin film transistor liquid crystal display (a-si tft lcd) panel structure with driver lsis for driving the tft (thin film transistor) array and a backlight. the a-si tft lcd panel structure is injected liquid crystal material into a narrow gap between the tft array glass substrate and a color-filter glass substrate. color (red, green, blue) data signals from a host system (e.g. pc, signal generator, etc.) are modulated into best form for active matrix system by a signal processing board, and sent to the driver lsis which drive the individual tft arrays. the tft array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly, when it is controlled by data signals. color images are created by regulating the amount of transmitted light through the tft array of red, green and blue dots. 1.2 applications ? ews monitors ? monitors for cad system 1.3 features ? ultra-wide viewing angle (with lateral electric field) ? high resolution ? low reflection ? 4port-lvds interface ? high luminance ? small foot print ? incorporated edge light type backlight (inverter less) www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 5 2. general specifications display area 433.152 (w) 324.864 (h) mm (typ.) diagonal size of display 54 cm (21.3 inches) drive system a-si tft active matrix display color 16,777,216 colors pixel 2048 (h) 1536 (v) pixels pixel arrangement rgb (red dot, green dot, blue dot) vertical stripe dot pitch 0.0705 (w) 0.2115 (h) mm pixel pitch 0.2115 (w) 0.2115 (h) mm module size 457.0 (w) 350.0 (h) 25.0 (d) mm (typ.) weight 4400 g (typ.) contrast ratio 500:1 (typ.) viewing angle at the contrast ratio 10:1 ? horizontal: right side 85 (typ.), left side 85 (typ.) ? vertical: up side 85 (typ.), down side 85 (typ.) designed viewing direction viewing angle with optimum grayscale ( =2.2): normal axis polarizer surface tbd polarizer pencil-hardness tbd h (min.) [by jis k5400] color gamut at lcd panel center 72 % (typ.) [against ntsc color space] response time ton (black 10% white 90%)+toff (white 90% black 10%) tbd ms (typ.) luminance at ibl= (6.5)marms / lamp 235 cd/m 2 (typ.) signal system 4 ports lvds interface (equivalent of thc63lvd824 2pcs, thine electronics, inc.) rgb 8-bit signals, data enable signal (de) power supply voltage lcd panel signal processing board: 12.0v backlight edge light type: 6 cold cathode fluorescent lamps, inverter less power consumption at checkered flag pattern and ibl= (6.5)marms / lamp tbd w (typ.) www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 6 3. block diagram note1: gnd is signal ground for logic and lcd driving. gnd and fg (frame ground) are not connected together in the lcd module. these grounds should be connected in customer equipment. i/f lcd module controller v-driver vdd gnd powe r supply for drivers h-driver v-driver 6144 lines tft lcd panel h: 2048 3 (r,g,b) v: 1536 1536 lines dc/dc converter dc0+/? dc1+/? dc2+/? ckc+/? dc3+/? dd0+/? dd1+/? dd2+/? ckd+/? dd3+/? cs sclk sdat bsel0 bsel1 da0+/? da1+/? da2+/? cka+/? da3+/? db0+/? db1+/? db2+/? ckb+/? db3+/? backlight (edge light type) vblh lamp lamp lamp vblc fg equivalent of thc63lvd824 (thine) equivalent of thc63lvd824 (thine) www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 7 4. detailed specifications 4.1 mechanical specifications parameter specification unit module size 457.0 1.0 (w) 350.0 1.0 (h) 25.0 0.5 (d) note1 mm display area 433.152 (w) 324.864 (h) note1 mm weight 4400 (typ.), tbd (max.) g note1: see " 7. outline drawings ". 4.2 absolute maximum ratings parameter symbol rating unit remarks lcd panel signal processing board vdd -0.3 to +15.0 v power supply voltage lamp voltage vblh tbd vrms ta = 25 c display signals note1 vd -0.3 to +3.6 v input voltage for signals function signals note2 vf -0.3 to +3.9 v ta = 25 c vdd=12.0v storage temperature tst -20 to +60 c - front surface topf 0 to +55 c note3 operating temperature rear surface topr 0 to + tbd c note4 95 % ta 40 c 85 % 40 < ta 50 c relative humidity note5 rh 70 % 50 < ta 55 c absolute humidity note5 ah 73 note6 g/m 3 ta > 55 c note1: da0+/-, da1+/-, da2+/-, da3+/-, cka+/-, db0+/-, db1+/-, db2+/-, db3+/-, ckb+/-, dc0+/-, dc1+/-, dc2+/-, dc3+/-, ckc+/-, dd0+/-, dd1+/-, dd2+/-, dd3+/-, ckd+/-. note2: cs, sclk, sdat, bsel0, bsel1 note3: measured at center of lcd panel surface (including self-heat) note4: measured at center of lcd module's rear shield surface (including self-heat) note5: no condensation note6: ta = 55c, rh = 70% www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 8 4.3 electrical characteristics 4.3.1 driving for lcd panel signal processing board (ta = 25 c) parameter symbol min. typ. max. unit remarks supply voltage vdd 10.8 12.0 13.2 v - ripple voltage vrp - - 100 mv for vdd differential input "l" threshold voltage vitl -100 - - mv differential input "h" threshold voltage vith - - +100 mv at vcm=1.2v vcm: common mode voltage for lvds driver note1 input voltage width vi 0 - 2.4 v - terminating resistor rt - 100 - ? - logic input "l" level vicl 0 - 0.8 v logic input "l" level vich open note3 - logic input "l" current iicl -10 - 10 a note2 supply current idd - (700) note4 tbd note5 ma at vdd=12.0v note1: da0+/-, da1+/-, da2+/-, da3+/-, cka+/-, db0+/-, db1+/-, db2+/-, db3+/-, ckb+/-, dc0+/-, dc1+/-, dc2+/-, dc3+/-, ckc+/-, dd0+/-, dd1+/-, dd2+/-, dd3+/-, ckd+/-. note2: cs, sclk, sdat, bsel0, bsel1 note3: "h" must be "open". note4: checkered flag pattern (by eiaj ed-2522) note5: pattern for maximum current www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 9 4.3.2 driving for backlight lamp (ta= 25 c, note1) parameter symbol min. typ. max. unit remarks lamp current ibl tbd (6.5) tbd marms at ibl=6.5marms: cd/m 2 note3 lamp voltage vblh - (800) - vrms note2,note3 (1220) - - vrms ta = 25 c note2, note3 lamp starting voltage vs (1460) - - vrms ta = 0 c note2, note3 oscillation frequency fo tbd (56) tbd khz note4 note1: this product's backlight consists of 6 lamps, and these specifications are for each lamp. note2: the lamp voltage cycle between lamps should be kept on a same phase. "vs" and "vblh" are the voltage value between low voltage side (cold) and high voltage side (hot). note3: the asymmetric ratio of working waveform for lamps (lamp voltage peak ratio, lamp current peak ratio and waveform space ratio) should be less than 5 % (see the following figure.). if the waveform is asymmetric, dc (direct current) element apply into the lamp. in this case, a lamp lifetime may be shortened, because a distribution of a lamp enclosure substance inclines toward one side between low voltage terminal (cold terminal) and high voltage terminal (hot terminal). pa: supply voltage/current peak for positive, pb: supply voltage/current peak for negative sa: waveform space for positive part, sb: waveform space for negative part note4: in case "fo" is not the recommended value, beat noise may display on the screen, because of interference between "fo" and "1/th". recommended value of "fo" is as following. th: horizontal cycle period (see " 4.12.1 input signal specifications ".) n: natural number (1, 2, 3 ???????? ) note5: method of lamp cable installation may invite fluctuation of lamp current and voltage or asymmetric of lamp working waveform. when designing method of lamp cable installation, evaluate the fluctuation of lamp current, voltage and working waveform sufficiently. fo = 1 4 1 th (2n-1) pa pb sa sb 0 ? pa - pb ? pb 100 5 % ? sa - sb ? sb 100 5 % 2 www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 10 4.3.3 power supply voltage ripple this product works, even if the ripple voltage levels are beyond the permissible values as following the table, but there might be noise on the display image. parameter power supply voltage ripple voltage note1 (measure at input terminal of power supply) unit vdd 12.0 v 100 mvp-p note1: the permissible ripple voltage includes spike noise. 4.3.4 fuse fuse parameter type supplier rating fusing current remarks tbd a vdd tbd tbd tbd v tbd a note1 note1: the power supply capacity should be more than the fusing current. if the power supply capacity is less than the fusing current, the fuse may not blow for a short time, and then nasty smell, smoking and so on may occur. www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 11 4.4 power supply voltage sequence note1: lvds signals should be measured at the terminal of 100 ? resistor. note2: in terms of voltage variation (voltage drop) while vdd rising edge is below 10.8v, a protection circuit may work, and then this product may not work. note3: lvds signals must be low or high-impedance, exclude the valid period (see above sequence diagram), in order to avoid that internal circuits is damaged. if some of display and function signals of this product are cut while this product is working, even if the signal input to it once again, it might not work normally. if customer stops the display and function signals, they should be cut vdd. note4: the backlight power supply voltage should be inputted within the valid period, in order to avoid unstable data display. valid period 10ms 50ms vdd on vdd off www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 12 4.5 connections and functions for interface pins 4.5.1 lcd panel signal processing board cn1 socket (lcd module side): fi-we41p-hf (japan aviation electronics industry limited (jae)) adaptable plug: fi-w41s (japan aviation electronics industry limited (jae)) pin no. symbol function description pin no. symbol function description 1 rsvd1 this terminal must be set to low. 21 db1+ 2 n.c. keep this terminal open. 22 db1- pixel data b1 lv d s differential signal 3 cs chip selection 23 gnd ground signal ground 4 sclk serial clock 24 db0+ 5 sdat serial data see "4.7 10-bit look up table for gamma adjustment". 25 db0- pixel data b0 lv d s differential signal 6 rsvd2 26 gnd ground signal ground 7rsvd2 keep this terminal open. 27 da3+ 8 bsel0 28 da3- pixel data a3 lv d s differential signal 9bsel1 selection of bit mapping mode see "4.6 method of connection for lvds transmitter". 29 gnd ground signal ground 10 rsvd2 keep this terminal open. 30 cka+ 11 gnd ground signal ground 31 cka- pixel clock a lv d s differential signal 12 db3+ 32 gnd ground signal ground 13 db3- pxel data b3 lv d s differential signal 33 da2+ 14 gnd ground signal ground 34 da2- pixel data a2 lv d s differential signal 15 ckb+ 35 gnd ground signal ground 16 ckb- pixel clock b lv d s differential signal 36 da1+ 17 gnd ground signal ground 37 da1- pixel data a1 lv d s differential signal 18 db2+ 38 gnd ground signal ground 19 db2- pixel data b2 lv d s differential signal 39 da0+ 20 gnd ground signal ground 40 da0- pixel data a0 lv d s differential signal 41 gnd ground signal ground note1: twist pair wires with 100 ? (characteristic impedance) should be connected between lcd panel signal processing board and lvds transmitter. 41 39 ??? 3 1 40 38 ??? 4 2 cn1: figure of socket www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 13 cn2 socket: fi-we31p-hf (japan aviation electronics industry limited (jae)) adaptable plug: fi-w31s (japan aviation electronics industry limited (jae)) pin no. symbol function description pin no. symbol function description 1 gnd ground signal ground 16 gnd ground signal ground 2 dd3+ 17 dc3+ 3 dd3- pixel data d3 lv d s differential signal 18 dc3- pixel data c3 lv d s differential signal 4 gnd ground signal ground 19 gnd ground signal ground 5 ckd+ 20 ckc+ 6 ckd- pixel clock d lv d s differential signal 21 ckc- pixel clock c lv d s differential signal 7 gnd ground signal ground 22 gnd ground signal ground 8 dd2+ 23 dc2+ 9 dd2- pixel data d2 lv d s differential signal 24 dc2- pixel data c2 lv d s differential signal 10 gnd ground signal ground 25 gnd ground signal ground 11 dd1+ 26 dc1+ 12 dd1- pixel data d1 lv d s differential signal 27 dc1- pixel data c1 lv d s differential signal 13 gnd ground signal ground 28 gnd ground signal ground 14 dd0+ 29 dc0+ 15 dd0- pixel data d0 lv d s differential signal 30 dc0- pixel data c0 lv d s differential signal 31 gnd ground signal ground note1: twist pair wires with 100 ? (characteristic impedance) should be connected between lcd panel signal processing board and lvds transmitter. cn3 socket (lcd module side): il-z-8pl-smty (japan aviation electronics industry limited (jae)) adaptable plug: il-z-8s-s125c (japan aviation electronics industry limited (jae)) pin no. symbol function description 1 vdd 2 vdd 3 vdd 4 vdd power supply - 5 gnd 6 gnd 7 gnd 8 gnd ground - 31 29 ??? 3 1 30 28 ??? 4 2 cn2: figure of socket 8 7 ....... 2 1 cn3: figure of socket www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 14 4.5.2 backlight inverter attention: vblh and vblc must be connected correctly. if customer connects wrongly, customer will be hurt and the module will be broken. cn201-cn206 plug (module side): bhsr-02vs-1 (j.s.t. mfg co., ltd.) adaptable socket: sm02b-bhss-1-tb (j.s.t. mfg co., ltd.) pin no. symbol function remarks 1 vblh high voltage (hot) cable color: tbd 2 vblc low voltage (cold) cable color: tbd 4.5.3 positions of plugs and sockets 1 2 cn204 1 2 cn205 1 2 cn206 1 2 cn201 1 2 cn202 1 2 cn203 cn1 cn2 cn3 31 1 41 1 8 1 insert direction www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 15 4.6 method of connection for lvds transmitter lvds data bit mapping mode is selectable with bsel0 and bsel1 terminal. bit mapping transmitter pin assign bsel[1:0] note1 dual type lvds tx cn1 [h:h], [l:l] [h:l] [l:h] single type lvds tx thine thc63lvd823 ns ds90c387 output connector pin no. signal name r2 r7 r0 ta0 r12 r10 r3 r6 r1 ta1 r13 r11 r4 r5 r2 ta2 r14 r12 ata- 40 da0- r5 r4 r3 ta3 r15 r13 ata+ 39 da0+ r6 r3 r4 ta4 r16 r14 r7 r2 r5 ta5 r17 r15 g2 g7 g0 ta6 g12 g10 g3 g6 g1 tb0 g13 g11 g4 g5 g2 tb1 g14 g12 g5 g4 g3 tb2 g15 g13 atb- 37 da1- g6 g3 g4 tb3 g16 g14 atb+ 36 da1+ g7 g2 g5 tb4 g17 g15 b2 b7 b0 tb5 b12 b10 b3 b6 b1 tb6 b13 b11 b4 b5 b2 tc0 b14 b12 b5 b4 b3 tc1 b15 b13 b6 b3 b4 tc2 b16 b14 atc- 34 da2- b7 b2 b5 tc3 b17 b15 atc+ 33 da2+ hsync hsync hsync tc4 hsync hsync vsync vsync vsync tc5 vsync vsync de de de tc6 de de r0 r1 r6 td0 r10 r16 r1 r0 r7 td1 r11 r17 g0 g1 g6 td2 g10 g16 atd- 28 da3- g1 g0 g7 td3 g11 g17 atd+ 27 da3+ b0 b1 b6 td4 b10 b16 b1 b0 b7 td5 b11 b17 n.c. n.c. n.c. td6 - - 31 cka- pixel data a clk clk clk clk clk clk at c l k - at c l k + 30 cka+ r2 r7 r0 ta0 r22 r20 r3 r6 r1 ta1 r23 r21 r4 r5 r2 ta2 r24 r22 bta- 25 db0- r5 r4 r3 ta3 r25 r23 bta+ 24 db0+ r6 r3 r4 ta4 r26 r24 r7 r2 r5 ta5 r27 r25 g2 g7 g0 ta6 g22 g20 g3 g6 g1 tb0 g23 g21 g4 g5 g2 tb1 g24 g22 g5 g4 g3 tb2 g25 g23 btb- 22 db1- g6 g3 g4 tb3 g26 g24 btb+ 21 db1+ g7 g2 g5 tb4 g27 g25 b2 b7 b0 tb5 b22 b20 b3 b6 b1 tb6 b23 b21 b4 b5 b2 tc0 b24 b22 b5 b4 b3 tc1 b25 b23 b6 b3 b4 tc2 b26 b24 btc- 19 db2- b7 b2 b5 tc3 b27 b25 btc+ 18 db2+ hsync hsync hsync tc4 hsync hsync vsync vsync vsync tc5 vsync vsync de de de tc6 de de r0 r1 r6 td0 r20 r26 r1 r0 r7 td1 r21 r27 g0 g1 g6 td2 g20 g26 btd- 13 db3- g1 g0 g7 td3 g21 g27 btd+ 12 db3+ b0 b1 b6 td4 b20 b26 b1 b0 b7 td5 b21 b27 n.c. n.c. n.c. td6 - - 16 ckb- pixel data b clk clk clk clk clk clk btclk- btclk+ 15 ckb+ note1: "h" must be "open". www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 16 bsel[1:0] note1 dual type lvds tx cn2 [h:h], [l:l] [h:l] [l:h] single type lvds tx thine thc63lvd823 ns ds90c387 output connector pin no. signal name r2 r7 r0 ta0 r12 r10 r3 r6 r1 ta1 r13 r11 r4 r5 r2 ta2 r14 r12 cta- 30 dc0- r5 r4 r3 ta3 r15 r13 cta+ 29 dc0+ r6 r3 r4 ta4 r16 r14 r7 r2 r5 ta5 r17 r15 g2 g7 g0 ta6 g12 g10 g3 g6 g1 tb0 g13 g11 g4 g5 g2 tb1 g14 g12 g5 g4 g3 tb2 g15 g13 ctb- 27 dc1- g6 g3 g4 tb3 g16 g14 ctb+ 26 dc1+ g7 g2 g5 tb4 g17 g15 b2 b7 b0 tb5 b12 b10 b3 b6 b1 tb6 b13 b11 b4 b5 b2 tc0 b14 b12 b5 b4 b3 tc1 b15 b13 b6 b3 b4 tc2 b16 b14 ctc- 24 dc2- b7 b2 b5 tc3 b17 b15 ctc+ 23 dc2+ hsync hsync hsync tc4 hsync hsync vsync vsync vsync tc5 vsync vsync de de de tc6 de de r0 r1 r6 td0 r10 r16 r1 r0 r7 td1 r11 r17 g0 g1 g6 td2 g10 g16 ctd- 18 dc3- g1 g0 g7 td3 g11 g17 ctd+ 17 dc3+ b0 b1 b6 td4 b10 b16 b1 b0 b7 td5 b11 b17 n.c. n.c. n.c. td6 - - 21 ckc- pixel data c clk clk clk clk clk clk ctclk- ctclk+ 20 ckc+ r2 r7 r0 ta0 r22 r20 r3 r6 r1 ta1 r23 r21 r4 r5 r2 ta2 r24 r22 dta- 15 dd0- r5 r4 r3 ta3 r25 r23 dta+ 14 dd0+ r6 r3 r4 ta4 r26 r24 r7 r2 r5 ta5 r27 r25 g2 g7 g0 ta6 g22 g20 g3 g6 g1 tb0 g23 g21 g4 g5 g2 tb1 g24 g22 g5 g4 g3 tb2 g25 g23 dtb- 12 dd1- g6 g3 g4 tb3 g26 g24 dtb+ 11 dd1+ g7 g2 g5 tb4 g27 g25 b2 b7 b0 tb5 b22 b20 b3 b6 b1 tb6 b23 b21 b4 b5 b2 tc0 b24 b22 b5 b4 b3 tc1 b25 b23 b6 b3 b4 tc2 b26 b24 dtc- 9 dd2- b7 b2 b5 tc3 b27 b25 dtc+ 8 dd2+ hsync hsync hsync tc4 hsync hsync vsync vsync vsync tc5 vsync vsync de de de tc6 de de r0 r1 r6 td0 r20 r26 r1 r0 r7 td1 r21 r27 g0 g1 g6 td2 g20 g26 dtd- 3 dd3- g1 g0 g7 td3 g21 g27 dtd+ 2 dd3+ b0 b1 b6 td4 b20 b26 b1 b0 b7 td5 b21 b27 n.c. n.c. n.c. td6 - - 6 ckd- pixel data d clk clk clk clk clk clk dtclk- dtclk+ 5 ckd+ note1: "h" must be "open". www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 17 4.7 10-bit look up table for gamma adjustment tbd 4.8 display colors and input data signals this product can display in equivalent to 16,777,216 colors in 256 scale. also the relation between display colors and input data signals is as the following table. data signal (0: low level, 1: high level) ra7 ra6 ra5 ra4 ra3 ra2 ra1 ra0 ga7 ga6 ga5 ga4 ga3 ga2 ga1 ga0 ba7 ba6 ba5 ba4 ba3 ba2 ba1 ba0 rb7 rb6 rb5 rb4 rb3 rb2 rb1 rb0 gb7 gb6 gb5 gb4 gb3 gb2 gb1 gb0 bb7 bb6 bb5 bb4 bb3 bb2 bb1 bb0 rc7 rc6 rc5 rc4 rc3 rc2 rc1 rc0 gc7 gc6 gc5 gc4 gc3 gc2 gc1 gc0 bc7 bc6 bc5 bc4 bc3 bc2 bb1 bb0 display colors rd7 rd6 rd5 rd4 rd3 rd2 rd1 rd0 gd7 gd6 gd5 gd4 gd3 gd2 gd1 gd0 bd7 bd6 bd5 bd4 bd3 bd2 bd1 bd0 basic colors black blue red magenta green cyan yellow white 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 red grayscale black dark bright red 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 : : 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green grayscale black dark bright green 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 : : 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue grayscale black dark bright blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 : : 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 18 4.9 display positions d(0, 0) d(1, 0) ??? d(2047,0) d(0, 1) d(1, 1) ??? d(2047,1) ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? d(0,1535) d(1,1535) ??? d(2047,1535) 4.10 pixel arrangnment 0 1 2047 0 rgb rgb ? ? ? ? ? ? ? rgb ??? ??? ? ? ? ? ? ? ? ??? 1535 rgb rgb ? ? ? ? ? ? ? rgb 4.11 lvds data taransmission method ra_int(7:0) ga_int(7:0) ba_int(7:0) rb_int(7:0) gb_int(7:0) bb_int(7:0) clk1_int d0(7:0) d2(7:0) d4(7:0) d1(7:0) d3(7:0) d5(7:0) rc_int(7:0) gc_int(7:0) bc_int(7:0) rd_int(7:0) gd_int(7:0) bd_int(7:0) clk2_int d1024(7:0) d1026(7:0) d1028(7:0) d1025(7:0) d1027(7:0) d1029(7:0) 2 www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 19 4.12 input signal timings for lcd panel signal processing board 4.12.1 input signal specifications parameter symbol min. typ. max. unit remarks frequency 1/ tc tbd - 65.00 15.38 tbd - mhz ns - duty - -- clk1 clk2 rise, fall - note1 ns - horizontal period th tbd tbd 10.339 672 tbd tbd s clk typ.=96.72khz horizontal display period thd 512 clk - vertical period tv tbd tbd 16.667 1612 tbd tbd ms h typ.=60.0hz vertical display period tvd 1536 h - clk-de set-up - ns - clk-de hold - ns - de1 de2 raise,fall - note1 ns - clk-data set-up - ns - clk-data hold - ns - data (a) to (d) rise, fall - note1 ns - note1: timing specifications are defined by the input signals of lvds transmitter. thc63lvd823 (thine) or equivalent products are recommended for lvds transmitter. note2: both of ?time? and ?clk number? of the ?th? must keep the minimum value of specification. note3: during operation, fluctuation of hsync period must not exceed 1 clk. otherwise function errors will occur in lcd module. e.g.: acceptable fluctuation range is 699-701 clk, when the hsync period is 700 clk. 2 www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 20 4.12.2 input signals timing chart tc invalid invalid de dotclk data (a) to (d) de de tvd=1536h(fixed) tv thd=512clk (fixed) th invalid invalid invalid invalid www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 21 4.13 optics 4.13.1 optical characteristics parameter note1 condition symbol min. typ. max. unit remarks luminance white at center r = 0 , l = 0 , u = 0 , d = 0 l tbd 235 - cd/m 2 - contrast ratio white/black at center r = 0 , l = 0 , u = 0 , d = 0 cr tbd 500 - - note2 luminance uniformity - lu - tbd 1.3 - note3 x coordinate wx - (0.313) - - white y coordinate wy - (0.319) - - x coordinate rx - tbd -- red y coordinate ry - tbd -- x coordinate gx - tbd -- green y coordinate gy - tbd -- x coordinate bx - tbd -- chromaticity blue y coordinate by - tbd -- color gamut r = 0 , l = 0 , u = 0 , d = 0 at center, against ntsc color space ctbd72 - % note4 black to white ton - tbd tbd ms response time white to black toff - tbd tbd ms note5 note6 right u = 0 , d = 0 , cr = 10 r (70) 85 - left u = 0 , d = 0 , cr = 10 l (70) 85 - up r = 0 , l = 0 , cr = 10 u (70) 85 - viewing angle down r = 0 , l = 0 , cr = 10 d (70) 85 - note7 note1: measurement conditions are as follows. ta = 25 c, vdd = 12v, ibl = 6.5marms/lamp, display mode: qxga, horizontal cycle = 95.34khz, vertical cycle = 60.0hz optical characteristics are measured at luminance saturation after 20minutes from working the product, in the dark room. also measurement method for luminance is as follows. note2: see " 4.13.2 definition of contrast ratio ". note3: see " 4.13.3 definition of luminance uniformity ". note4: these coordinates are found on cie 1931 chromaticity diagram. note5: product surface temperature: topf = tbd c note6: see " 4.13.4 definition of response times ". note7: see " 4.13.5 definition of viewing angles ". 1 photodetector (topcon bm-5a) lcd module (product) 50cm www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 22 4.13.2 definition of contrast ratio the contrast ratio is calculated by using the following formula. luminance of white screen luminance of black screen 4.13.3 definition of luminance uniformity the luminance uniformity is calculated by using following formula. maximum luminance from to minimum luminance from to the luminance is measured at near the 5 points shown below. 4.13.4 definition of response times response time is measured, the luminance changes from "black" to "white", or "white" to "black" on the same screen point, by photo-detector. ton is the time it takes the luminance change from 10% up to 90%. also toff is the time it takes the luminance change from 90% down to 10% (see the following diagram.). 4.13.5 definition of viewing angles contrast ratio (cr) = luminance uniformity (lu) = 100% 90% 10% 0% ton toff luminance white black left upper lower n ormal axis (perpendicular) u d r l 12 o?clock right 342 1024 1708 256 768 1280 www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 23 5. reliability tests test item condition judgment note1 high temperature and humidity (operation) 60 2 c, rh = 60%, 240hours display data is white. heat cycle (operation) 0 3 c 1hour 55 3 c 1hour 50cycles, 4hours/cycle display data is white. thermal shock (non operation) -20 3 c 30minutes 60 3 c 30minutes 100cycles, 1hour/cycle temperature transition time is within 5 minutes. no display malfunctions vibration (non operation) 5 to 100hz, 11.76m/s 2 1 minute/cycle x, y, z direction 10 times each directions mechanical shock (non operation) 294m/ s 2 , 11ms x, y, z direction 3 times each directions no display malfunctions no physical damages esd (operation) 150pf, 150 ? , 10kv 9 places on a panel surface note2 10 times each places at 1 sec interval dust (operation) sample dust: no.15 (by jis-z8901) 15 seconds stir 8 times repeat at 1 hour interval operation 53.3 kpa 0 c 3 c 24 hours 55 c 3 c 24 hours low pressure non- operation 15 kpa -20 c 3 c 24 hours 60 c 3 c 24 hours no display malfunctions note1:display and appearance are checked under environmental conditions equivalent to the inspection conditions of defect criteria. note2: see the following figure for discharge points www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 24 6. precautions 6.1 meaning of caution signs the following caution signs have very important meaning. be sure to read "6.2 cautions" and "6.3 attentions", after understanding this contents! ! this sign has the meaning that customer will be injured by himself or the product will sustain a damage, if customer has wrong operations. this sign has the meaning that customer will get an electrical shock, if customer has wrong operations. this sign has the meaning that customer will be injured by himself, if customer has wrong operations. 6.2 cautions ? ? ? ? do not touch the working backlight. customer will be in danger of an electric shock. ? ? ? ? do not touch the working backlight. customer will be in danger of burn injury. ? ? ? ? do not shock and press the lcd panel and the backlight! there is a danger of breaking, because they are made of glass. (shock: to be not greater 294m/s 2 and to be not greater 11ms, pressure: to be not greater tbd n) 6.3 attentions ! 6.3.1 handling of the product take hold of both ends without touch the circuit board cover when customer pulls out products (lcd modules) from inner packing box. if customer touches it, products may be broken down or out of adjustment, because of stress to mounting parts. do not hook cables nor pull connection cables such as lamp cable and so on, for fear of damage. if customer puts down the product temporarily, the product puts on flat subsoil as a display side turns down. take the measures of electrostatic discharge such as earth band, ionic shower and so on, when customer deals with the product, because products may be damaged by electrostatic. the torque for mounting screws must never exceed tbd n ? m. higher torque values might result in distortion of the bezel. the product must be installed using mounting holes without undue stress such as bends or twist (see outline drawings). and do not add undue stress to any portion (such as bezel flat area) except mounting hole portion. bends or twist described above and undue stress to any portion except mounting hole portion may cause display un-uniformity. www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 25 do not press or rub on the sensitive display surface. if customer clean on the panel surface, nec recommends using the cloth with ethanolic liquid such as screen cleaner for lcd. do not push-pull the interface connectors while the product is working, because wrong power sequence may break down the product. do not bend or unbend the lamp cable at the near part of the lamp holding rubber, to avoid the damage for high voltage side of the lamp. this damage may cause a lamp breaking and abnormal operation of high voltage circuit. 6.3.2 environment do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases. keep the product in antistatic pouch in room temperature, because of avoidance for dusts and sunlight, if customer stores the product. in order to prevent dew condensation occurring by temperature difference, the product packing box must be opened after leave under the environment of an unpacking room temperature enough. because a situation of dew condensation occurring is changed by the environmental temperature and humidity, evaluate the leaving time sufficiently. (recommendation leaving time: 6 hour or more with packing state) do not operate in high magnetic field. circuit boards may be broken down by it. this product is not designed as radiation hardened. use an original protection sheet on the product surface (polarizer). adhesive type protection sheet should be avoided, because it may change color or properties of the polarizer. 6.3.3 characteristics the following items are neither defects nor failures. response time, luminance and color may be changed by ambient temperature. the lcd may be seemed luminance non-uniformity, flicker, vertical seam or small spot by display patterns. optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change depending on operating time, and especially low temperature, because the lcd has cold cathode fluorescent lamps. do not display the fixed pattern for a long time because it may cause image sticking. use a screen saver, if the fixed pattern is displayed on the screen. the display color may be changed by viewing angle because of the use of condenser sheet in the backlight. optical characteristics may be changed by input signal timings. the interference noise of input signal frequency for this product's signal processing board and luminance control frequency of customer's backlight inverter may appear on a display. set up luminance control frequency of backlight inverter so that the interference noise does not appear. 6.3.4 other all gnd and vdd terminals should be connected without a non-connected signal line. do not disassemble a product or adjust volume without permission of nec. pay attention not to insert waste materials inside of products, if customer uses screwnails. pack the product with original shipping package, because of avoidance of some damages during transportation, when customer returns it to nec for repair and so on. not only the module but also the equipment that used the module should be packed and transported as the module becomes vertical. otherwise, there is the fear that a display dignity decreases by an impact or vibrations. www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 26 7. outline drawings 7.1 front view unit: mm n ote1: the torque for mounting screw should never exceed tbd n ? m. n ote2: the values in parentheses are for reference. 2 www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 27 7.2 rear view unit: mm n ote1: the torque for mounting screw should never exceed tbd n ? m. n ote2: the values in parentheses are for reference. www.datasheet.co.kr datasheet pdf - http://www..net/
NL204153BC21-02 preliminary data sheet dod-pd-0092 (2nd edition) 28 revision history the inside of latest specifications is revised to the clerical error and the major improvement of previous edition. only a changed part such as functions, characteristic value and so on that may affect a design of customers, are described especially below. edition document number prepared date revision contents and signature 1st edition dod-pd- 0052 may 15, 2003 revision contents new issue 2nd edition dod-pd- 0092 july 4, 2003 revision contents p9 driving for backlight lamp- lamp starting voltage (vs): ? ta= 25 c: (1000) vrms (1220) vrms ? ta= 0 c: (1300) vrms (1460) vrms p18 "lvds data transmission method" is added. p19 input signal specifications are changed. p26 outline drawings: front view is changed. r. kawashima a pproved by checked by p repared b y signature of writer t. i to a pproved by t. i to checked by p repared b y r. kawashima signature of writer www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of NL204153BC21-02

	To Download NL204153BC21-02 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .